KOMPAS-3D v23

It is available in the following commands: Center mark, Centerline by Two Points, Arc centerline, Conditional intersection, Wavy line, Line with bends, Straight coordination axis, Circular Coordination Axis, Coordination Arc Axis.

Sometimes, it is required to create several same-typed designations having a number of identical parameters. To saving the values of these parameters before completion command running, the button Remember Status is used.

Set the values of parameters common for designations, then press the button Remember Status, after which continue building.

More information about remembering parameters...

Example 1. Creation of designations of center with an identical slope angle.

1.Invoke the Center mark command.

2.Select the type of designation of center using the Type group of buttons on the Parameter Panel and configure rendering using the elements of the Parameters sector.

3.Enter the value of slope angle of designation in the Slope angle field.

4.Please select Remember Status.

5.Sequentially indicate circles (an arc of circles) or set the central points of designations of the center.

Example 2. Building identical jogged lines of breaks.

1.Invoke the Line with bends command.

2.Configure rendering of the jogged line using elements of the Additional parameters sector on the Parameter Panel.

3.Set the values of length and slope angle of the jogged line in the Length and Angle fields.

4.Click the Remember Status button.

5.Sequentially indicate the starting points for creation of lines with bends.

Example 3. Creation of straight lines (longitudinal or transverse) coordination axes.

1.Invoke the Straight coordination axis command.

2.Set the length and slope angle of the axis in the Length and Angle fields.

3.Configure the settings of juts and marks using the elements of the Juts and marks sector on the Parameter Panel.

4.Click the Remember Status button.

5.Input designation of the axis and enable the Auto Continueoption.

6.Sequentially indicate the starting point of each created axis.

To create a grid of direct coordination axes, do the following actions. It is supposed that to arrange axes with a certain pitch, a markup was preliminarily created using auxiliary elements in the document.

1.Perform the requisite tasks. 1. Run steps 1–5 of the previous sequence of actions, having set value 0 in the Angle field.

2.Specify the starting points of the required number of horizontal axes.

3.In the Angle field, enter the value 90.

4.Enter the number of axis in the Text field.

5.Specify the starting points of required number of vertical axes.

Example 4. Creation of arc coordination axes in the form of arcs of concentric circles.

1.Invoke the Coordination Arc Axis command.

2.Configure the settings of juts and marks using the elements of the Juts and marks sector on the Parameter Panel.

3.Specify position of the center. Enter values in the Initial angle and End angle fields.

4.Press the button to Remember Status.

5.Input designation of the axis and enable the Auto Continueoption.

6.Sequentially indicate a point on each created axis or consistently enter values into the Radius field.

To build two groups of concentric arc axes symmetric relative to the direct line (for example, OY axis), do the following actions.

1.Build the first group of axes, performing steps. 1–6 of the previous sequence of actions.

2.Edit the value in the Starting angle field by transforming it to a difference between 180 and the current value. To do this, activate the field and, without changing the current value, enter before it the characters 180- and press the key <Enter>.

3.Similarly, edit value in the End anglefield.

4.Change the direction of building an axis.

5.Unfix the Center field by clicking the icon and specify the center of the new group of axes.

6.Sequentially indicate a point on each created axis or consistently enter values into the Radius field.

Example 5. Creation of circular coordination axes in the form of concentric circles.

1.Invoke the Circular Coordination Axis command.

2.Configure the settings of marks using the elements of the Parameter Panel.

3.Set the center of the circle.

4.Click the button Remember Status.

5.Input designation of the axis and enable the Auto Continueoption.

6.Sequential indicate the points of arrangement of marks of the created axes.